diff options
Diffstat (limited to 'doc/rsyslog_conf.html')
| -rw-r--r-- | doc/rsyslog_conf.html | 28 |
1 files changed, 19 insertions, 9 deletions
diff --git a/doc/rsyslog_conf.html b/doc/rsyslog_conf.html index 1073cf5e..01e693e4 100644 --- a/doc/rsyslog_conf.html +++ b/doc/rsyslog_conf.html @@ -50,6 +50,8 @@ input plugin for plain tcp and GSS-enabled syslog</li> <li><a href="imklog.html">imklog</a> - kernel logging</li> <li><a href="imuxsock.html">imuxsock</a> - unix sockets, including the system log socket</li> +<li><a href="im3195.html">im3195</a> - +accepts syslog messages via RFC 3195</li> </ul> <p>Please note that each module provides configuration directives, which are NOT necessarily being listed below. Also @@ -114,19 +116,25 @@ default 60000 (1 minute)]</li> <li>$ActionQueueType [FixedArray/LinkedList/<b>Direct</b>/Disk]</li> <li>$ActionQueueSaveOnShutdown [on/<b>off</b>] </li> -<li>$ActionQueueWorkerThreads <number>, num -worker threads, default 1, recommended 1</li> -<li>$ActionQueueWorkerThreadMinumumMessages -<number>, default 100</li> +<li>$ActionQueueWorkerThreads <number>, num worker threads, default 1, recommended 1</li> +<li>$ActionQueueWorkerThreadMinumumMessages <number>, default 100</li> <li><a href="rsconf1_actionresumeinterval.html">$ActionResumeInterval</a></li> -<li>$ActionResumeRetryCount <number> [default 0, --1 means eternal]</li> +<li>$ActionResumeRetryCount <number> [default 0, -1 means eternal]</li> +<li>$ActionSendResendLastMsgOnReconn <[on/<b>off</b>]> specifies if the last message is to be resend when a connecition broken and has been reconnedcted. May increase reliability, but comes at the risk of message duplication. +<li>$ActionSendStreamDriver <driver basename> just like $DefaultNetstreamDriver, but for the specific action +</li><li>$ActionSendStreamDriverMode <mode>, default 0, mode to use with the stream driver +(driver-specific)</li><li>$ActionSendStreamDriverAuthMode <mode>, authentication mode to use with the stream driver +(driver-specific)</li><li>$ActionSendStreamDriverPermittedPeer <ID>, accepted fingerprint (SHA1) or name of remote peer +(driver-specific) -<span style="font-weight: bold;"> directive may go away</span>!</li> <li><a href="rsconf1_allowedsender.html">$AllowedSender</a></li> <li><a href="rsconf1_controlcharacterescapeprefix.html">$ControlCharacterEscapePrefix</a></li> <li><a href="rsconf1_debugprintcfsyslinehandlerlist.html">$DebugPrintCFSyslineHandlerList</a></li> <li><a href="rsconf1_debugprintmodulelist.html">$DebugPrintModuleList</a></li> <li><a href="rsconf1_debugprinttemplatelist.html">$DebugPrintTemplateList</a></li> +<li>$DefaultNetstreamDriver <drivername>, the default <a href="netstream.html">network stream driver</a> to use. Defaults to ptcp.$DefaultNetstreamDriverCAFile </path/to/cafile.pem></li> +<li>$DefaultNetstreamDriverCertFile </path/to/certfile.pem></li> +<li>$DefaultNetstreamDriverKeyFile </path/to/keyfile.pem></li> <li><a href="rsconf1_dircreatemode.html">$DirCreateMode</a></li> <li><a href="rsconf1_dirgroup.html">$DirGroup</a></li> <li><a href="rsconf1_dirowner.html">$DirOwner</a></li> @@ -347,6 +355,10 @@ all relatively recent versions of rsyslog. Other syslogd's may get hopelessly confused if receiving that format, so check before you use it. Note that the format is unlikely to change when the final RFC comes out, but this may happen.</li> +<li><span style="font-weight: bold;">RSYSLOG_DebugFormat</span> +- a special format used for troubleshooting property problems. This format +is meant to be written to a log file. Do <b>not</b> use for production or remote +forwarding.</li> </ul> <h2>Output Channels</h2> <p>Output Channels are a new concept first introduced in rsyslog @@ -505,9 +517,7 @@ filter on any property, like HOSTNAME, syslogtag and msg. A list of all currently-supported properties can be found in the <a href="property_replacer.html">property replacer documentation</a> (but keep in mind that only the properties, not the replacer is supported). With this filter, each properties can be checked against a -specified value, using a specified compare operation. Currently, there -is only a single compare operation (contains) available, but additional -operations will be added in the future.</p> +specified value, using a specified compare operation.</p> <p>A property-based filter must start with a colon in column 0. This tells rsyslogd that it is the new filter type. The colon must be followed by the property name, a comma, the name of the compare |